flyfisher842

@angelo_nwl

I am using the general CONTENTS trigger on my locations page to pull the locations list from the settings.

A trigger of SINGLE could be used to send the single location to that place on the locations page using the format for single would work ok I think.

@angelo_nwl

Angelo,

This would also work. I have chosen an elementor template named locations in the pages location/archives section and the formatting for the over all list goes to that page just fine. What is not happening is the link to the single location going to the same list page so the formatting for the single location can be applied.

What is get is the results of the single.php from the theme not my locations elementor template.

A simpler solution than what I suggested above would be to use the chosen locations archive page for both the list and the single location both controlled by the appropriate formatting section the in the formatting list.

@angelo_nwl

I am reopening this ticket. Was not able to get the href to work as I needed it but have identified an addition to the event manager settings that would fix this single location issue I think.

In the Formatting set > Location Pages is formatting for the overall list of locations targeted to the page chosen in the location pages Pages section.

In the formatting there is formatting for a single location but there is no place to chose the single location page in the pages section under location list/archives. This section allows you to set a target page for the overall list of locations controlled by the location formatting. Please add a section just below the overall list to chose a target page to display the single location information and my issue would be solved I think.

The overall list works fine with my elementor formatted template page and I see no reason that the same would not be true for a single location elementor page if the events manager had a chosen page to send the information to it.

I hope this change to the settings can be done. I also hope this will clarify my problem for you.

Thanks again for your help in resolving this issue.

I will give it a try. Thanks for the help. Never occurred to me to use the placeholders in a url format. I have used them to display data in certain formats successfully.

Yes I know. This site does not have pro activated on it. I am using Version 3.1.4 on this site. I thought I had turned off pro from this site and did delete the pro plug in from this site.

Actually I only have pro attached to one site and this is not it. This site is only operating the www.remarpro.com elementor which is why I posted here.

Not sure what was going on but as long as I load elementor from the classic editor everything is ok.

If this problem reoccurs I will to to the commercial support. I did not mean to cause any problems.

• This reply was modified 3 years, 7 months ago by flyfisher842.
• This reply was modified 3 years, 7 months ago by flyfisher842.

More accurate would be to take the pages produced from the locationlink in the em database and display them with a nice elementor header with a background image and a transparent header with the theme footer at the bottom of the single location information.

I have the template built with elementor for a single location but do not know hot to make the links in the locations list be displayed in the single location template

• This reply was modified 3 years, 7 months ago by flyfisher842.

Thanks for the prompt reply. I have to manually fix some of the pages with missing background images but the refresh help with other links. Thanks for the help. I think the 5.7.1 WP update may have been the problem as I had a different site also lose the featured image after the update.

Thanks for the help. Will do so.

• This reply was modified 3 years, 8 months ago by flyfisher842.

An admin user with the username XXXXXX was created outside of WordPress.
Type: Unknown Administrator
Issue Found 10/02/2020 2:17 pm
High

An admin user with the username xxxxxx was created outside of WordPress. It’s possible a plugin could have created the account, but if you do not recognize the user, we suggest you remove it.

We are a membership website. As a full admin, I probably logged in on the front end and went to the dashboard, then escalated xxxxx privileges to admin from contributor. xxxxx is the club president and I do not understand why wordfence does not understand I have the authority to do what I did.

@wfadam Apparently the last time I clicked the fixed button and saved the changes, it worked. So that message about an admin defined out of wordpress is gone. Not sure why WF should have put up a message anyway.

Just ran a new scan. Now I am getting messages about tinymce plugin being modified. Of course it was. I updated the plugin as requested.

Modified plugin file: wp-content/plugins/tinymce-advanced/plugin-assets/tadv.css
Type: File

WF is running down thru each file modified. I fixed this yesterday by clicking the fixed button for each file. And now it too is back again.

Probably tinymce has not updated the respository copy or wherever WF goes to get a copy to compare to what is on my site.

• This reply was modified 4 years, 1 month ago by flyfisher842.
• This reply was modified 4 years, 1 month ago by flyfisher842.

@davidanderson

It only relates to easy updates in this respect. If I install the jquery updater or similar plugin, will it be automatically added to the easy updates control panel?

I think this is more an issue for wordpress core forums but I cannot find a way to make a post in the Security forum under site hardening which is where I think it should go. Very frustrating.

@wfadam Thank you for accepting my data for review about the vulnerability issue I am concerned about. You have my email address so any replies to that address would be best.

Please close this thread as there is no closure button anymore.

@sterndata

Well I tried to submit my data to www.remarpro.com about the plugin I am having security issues with but it was rejected twice now at the approved email address provided in the submission info. So I am done with submitting to www.remarpro.com about this issue

Wordfence has the information and will do fine with letting me know about the issue.

Thanks for the help.

This is what I have been telling you. The old files are still there and there was no notification button or delete button. I had to use file manager on cpanel to delete them.

Deleting is not the problem. Updraft not working right and notifying when the old files were still there is the problem.

• This reply was modified 4 years, 4 months ago by flyfisher842.